- -30%
Herramienta de quemador de bolígrafo de soldadura de butano inalámbrico de hierro de soldadura de soplete de gas
Herramienta de quemador de bolígrafo de soldadura de butano inalámbrico de hierro de soldadura de soplete de gas
$ 12,24
30% de descuento
$ 17,49
Sin impuestos
Gas Blow Torch Soldering Solder Iron Cordless Butane Welding Pen Burner Tool
Gas Blow Torch Soldering Solder Iron Cordless Butane Welding Pen Burner Tool
Description:
1. Loose corroded metal screw kit, laboratory heating research, kitchen baking tools, factory equipment maintenance
2. Welding, car, truck, aviation repair, hydropower engineering repair
3. Repair of electrical appliances, motor control boxes, welding, etc.
4. Wire, circuit board repair and welding, IC board welding and repair, home field circuit welding, repair and maintenance, multifunctional use
Specifications:
*100% brand new and high quality
*Optional colors: green, blue
*Material: Plastic Metal
*Dimensions: 15.2*2 CM
*Input voltage: 1300 (V)
*Temperature range: 1300-450 (degree Celsius)
*Name: Pen-type gas soldering iron
*Filling capacity: 8ML
*Temperature: flame temperature 1300degree Celsius, soldering iron temperature 450degree Celsius
*Use fuel: pure butane
*Use time: 35-45 minutes
*Screw diameter: 0.5cm (approximately)
Package Contents:
1 pen-shaped gas soldering iron
1 set of soldering iron cutting head
Product Instructions :
*1. Filling gas
1. Use high-quality gas to fill the flush, and confirm that the switch is in the OFF position.
2.Introduce the gas tank into the air hole and press down to inflate.
3. About 10 seconds, the gas filling can be completed, wait a few minutes for the gas to stabilize, and then use it.
4.If the gas is filled in, and there is a hissing sound at the tail, use the pen tip to press into the air port to eliminate it.
*2. Ignition
1. Push the switch to the ON position and hear a "hissing" sound.
2.Push the flameout ring forward.
3.Use an igniter or lighter to ignite near the joint.
4. After lighting the fire, burn for 3 seconds, then return the flameout ring to the original place. When the fire is extinguished, the soldering iron tip will continue to heat up.
5. Adjust the size of the flame to increase in the direction of and small in the direction of --.
6.The product temperature is as high as 1300 degree Celsius (soldering iron temperature 450 degree Celsius). Please pay attention to safety when using it, and turn off the switch after use.
7.When using a gas soldering iron, please pay special attention to wait until the flame is completely eliminated, and when the object inside the soldering iron turns red, perform the operation again, and the flame size should not be large to extend the life of the soldering iron tip.
8. The length of the flame is about 1.2-1.5 cm
Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.
Gas Blow Torch Soldering Solder Iron Cordless Butane Welding Pen Burner Tool
Description:
1. Loose corroded metal screw kit, laboratory heating research, kitchen baking tools, factory equipment maintenance
2. Welding, car, truck, aviation repair, hydropower engineering repair
3. Repair of electrical appliances, motor control boxes, welding, etc.
4. Wire, circuit board repair and welding, IC board welding and repair, home field circuit welding, repair and maintenance, multifunctional use
Specifications:
*100% brand new and high quality
*Optional colors: green, blue
*Material: Plastic Metal
*Dimensions: 15.2*2 CM
*Input voltage: 1300 (V)
*Temperature range: 1300-450 (degree Celsius)
*Name: Pen-type gas soldering iron
*Filling capacity: 8ML
*Temperature: flame temperature 1300degree Celsius, soldering iron temperature 450degree Celsius
*Use fuel: pure butane
*Use time: 35-45 minutes
*Screw diameter: 0.5cm (approximately)
Package Contents:
1 pen-shaped gas soldering iron
1 set of soldering iron cutting head
Product Instructions :
*1. Filling gas
1. Use high-quality gas to fill the flush, and confirm that the switch is in the OFF position.
2.Introduce the gas tank into the air hole and press down to inflate.
3. About 10 seconds, the gas filling can be completed, wait a few minutes for the gas to stabilize, and then use it.
4.If the gas is filled in, and there is a hissing sound at the tail, use the pen tip to press into the air port to eliminate it.
*2. Ignition
1. Push the switch to the ON position and hear a "hissing" sound.
2.Push the flameout ring forward.
3.Use an igniter or lighter to ignite near the joint.
4. After lighting the fire, burn for 3 seconds, then return the flameout ring to the original place. When the fire is extinguished, the soldering iron tip will continue to heat up.
5. Adjust the size of the flame to increase in the direction of and small in the direction of --.
6.The product temperature is as high as 1300 degree Celsius (soldering iron temperature 450 degree Celsius). Please pay attention to safety when using it, and turn off the switch after use.
7.When using a gas soldering iron, please pay special attention to wait until the flame is completely eliminated, and when the object inside the soldering iron turns red, perform the operation again, and the flame size should not be large to extend the life of the soldering iron tip.
8. The length of the flame is about 1.2-1.5 cm
Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.
Política de seguridad
Política de entrega
Política de devolución
